Produse pentru industrie chimică românească (77)

The top-entry agitator LRK is used to meet rigorous requirements regarding both bearing and smooth-running. In addition to its rigid cast steel bearing housing, this agitator series features a coupling housing with an elastic coupling to connect the drive with a shaft journal. Thus, the LRK can be supplied as a fast running agitator with long shafts. The agitator shaft is borne within the bearing housing and is divided by a flanged coupling below the mounting flange. According to your tank size, the LRK series agitator is supplied in six different frame sizes. Shaft diameters of 40 mm to 130 mm with lengths of up to 12,000 mm can be realized. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3). Bearing housings with shaft seals of different materials are feasible, alternatively with stuffing boxes or mechanical seals.

Electrical tote tank mixers for stainless steel IBCs The LRK-C series tote tank mixer and their drive units LRK-A are a special solution designed for operation on stainless steel containers with filling openings of at least 400 mm and mixing volumes from 400 l up to 1,500 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The mixing unit that remains in the container is connected to the drive unit with a bayonet coupling and a clutch. The drive is dismountable so that one drive unit can be used for several mixer units interchangeable. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The agitator shafts are borne in a bearing housing, which is welded into the container lid on the product side. The impellers are designed to fit through the filling opening DN 400 when being inserted.

Side-entry agitator for mixing below liquid surface. The PDR is a simple side-entry-agitator for mixing below the liquid surface. The PDR is recommended for applications where low viscous liquids are mixed turbulently in high tanks and where a top-entry mixer would be too heavy due to its shaft length and –diameter. The sealing between the agitator and the vessel is done by means of a single-acting, internal mechanical seal which is lubricated by the mixing product or an additional fluid The agitator shaft is connected to the drive directly with a flange coupling inside the seal housing. By default, this agitator series is supplied with marine type propellers. Other mixing elements according to the mixing task upon request. Solutions correspond to those of the SPR, additionally mechanical seal in sealing housing. Other solutions for this series upon request.

Les processeurs Filmtruder et Viscon sont spécialisés dans la concentration, la purification et la dévolatilisation de produits ayant des viscosités allant jusqu'à 10.000 Pa (s) et sont caractérisés par les propriétés suivantes: Traitement en couche mince agitée Renouvellement inégalé du film agité entraînant les plus faibles contenus typiques de volatils résiduels En général ne nécessite pas d’agent de stripage Grand volume de vapeur libre par rapport à la rétention du produit, ce qui permet une élimination très rapide des matières volatiles en une seule étape Un système de traitement en couche mince performant consiste en une bonne conception du processeur combiné à des périphériques parfaitement adaptés à celui-ci. SMS peut fournir un système complet, y compris des services de montage, installation et démarrage.

The GRV series can be used in versatile manner. It is equipped with a mechanically variable speed variation drive with drive ratings of up to 11.0 kW. Furthermore it can be supplied with geared drives that have a standard output speed of between 1 and 1,750 rpm. The speed is adjustable with a hand wheel. The agitator shaft of the GRV series geared agitator is directly mounted on the shaft of the mechanical speed variator or with additional speed reduction (all before mentioned solutions possible). The agitator shafts are balanced for concentric run after assembly of the mixer. According to the specific mixing task, the GRV series can be supplied with matching mixing elements and various seals.

The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker.

The GRK series geared agitator equipped with a helical bevel geared drive with reinforced bearing can be used for a wide range of applications due to its low installation height. This ow installation height can be achieved thanks to the horizontal position of the drive. The agitator shaft of the GRK series is directly mounted in the hollow shaft of the gear and, upon request, this agitator shaft can be divided by flanged coupling. After assembly of the mixer, the agitator shafts are balanced for concentric run. The GRK series features shaft lengths of up to 6,000 mm and drive ratings of up to 75.0 kW. It has a standard output speed of 1 to 250 rpm. According to the specific mixing task, the GRK series can be supplied with matching mixing elements and various seals. Upon request, we supply the GRK series with frequency controlled drives that have drive ratings of up to 7.5 kW. Type test certificate for explosive zone 0.

The Large Volume Processor program consists of horizontally arranged, heated reactors with twin (co- or counterrotating) shaft which provide intensive mixing and kneading. The highly versatile large volume processors Reasil and Reacom are characterised by the following advantages: Very large volumes The highest viscosity melts (up to 15,000 Pas) and solids can be processed efficiently Low shear processing Long residence times are achieved economically Mixing, devolatilization, reaction and phase change (from melt to solid) can take place in the same machine. A successful devolatilization or reaction system consists of the right processor design integrated with properly engineered subsystems. SMS can provide a complete system, including installation and start-up services, or full engineering and design documentation to allow you to add the necessary subsystems for our high volume processors. Product viscosity:20-15.000 Pa·s /solids

Das SMS-Programm der großvolumigen Prozessoren besteht aus horizontalen, beheizten Reaktoren, 2-wellig, (gleich- oder gegenlaufend), die das viskose Produkt effektiv kneten und durchmischen. Die vielseitigen großvolumigen Prozessoren Reasil und Reacom haben im Wesentlichen die folgenden Merkmale: Sehr große Prozessvolumina Effiziente Behandlung von Produkten mit schwierigen/wechselnden Phasenübergängen Geringe Scherraten Wirtschaftliche Realisierung von langen Produktverweilzeiten Mischen, Entgasen, Reagieren und Phasenwechsel (von Schmelze bis Feststoff) in einer Maschine Ein erfolgreiches Entgasungs- und Reaktionssystem besteht immer aus der Kombination eines anwendungsspezifisch ausgelegten Reaktors und den zugehörigen peripheren Komponenten. Produktviskosität:20 - 15.000 Pa·s / Feststoff

The FRP is Geppert Ruhrtechnik’s fast running pneumatic air mixer that can be directly mounted on 200 l steel drums with a 2“ bung hole. The FRP is mounted onto the drum with a 2” threaded adapter. The agitator is screwed into the bung hole. We do offer one drive especially adapted for low viscous media and one drive especially adapted for medium viscous media of up to 1,000 mPas. The agitator shaft is connected to a bearing shaft within the drum mixer housing by means of a sleeve coupling. This bearing shaft is connected to the drive shaft. Folding propellers are used as agitator elements, which can be inserted into the drum through the 2” bung hole when being folded. As a mobile mixer, the FRP can be delivered as a turn-key machine with a service kit for the lubrication of the compressed air and a noise muffler.

The GRP is a pneumatic agitator equipped with either a helical geared drive or a worm geared drive. It is used for homogenizing, dispersing, emulsifying and suspending of low- and medium viscosity materials in small containers. The agitator shaft is directly mounted on the shaft journal. Elastic operation, in other words: The speed of the agitator adapts to the viscosity of the media being mixed. Compact and easy-to-maintain construction as well as low weight allows an easy handling. Speed is sensitively and continuously adjustable, smooth start, insensitive to vapor, dust and smoke. Compressed air keeps all moving parts clean. Insensitive to heat, suitable for high ambient temperatures. Compressed air expanding in the air engine cools the agitator drive. The pneumatic agitators are explosion proof and overload proof until standstill. Type test certificate for explosive zone 0.

The Reactotherm is a heavy duty processor with an intensive mixing and kneading effect and self-cleaning ability. It is used for thermal processing of a wide variety of pasty, viscous, and fouling products. It can be operated continuously or batch-wise. The Reactotherm consists of a cylindrical, horizontal shell and a rotor with segmented discs and mixing bars. Stationary mixing hooks are attached to the inside of the shell. The close clearance between the mixing hooks, the segmented discs and the rotor result in a high mixing and kneading effect and the self-cleaning properties of the rotor. The inside of the shell is cleaned by the mixing bars. Fouling of heat exchange surfaces and the formation of agglomerates are avoided. The shell, the rotor shaft and the discs can be heated or cooled. The product transport is accomplished by the slightly pitched mixing bars. Material:Stainless & carbon steel,

The tote tank mixers CRP-E are equipped with a pneumatic drive. It has been especially designed for plastic IBCs with filling openings of at least 150 mm and volumes from 600 l up to 1,200 l. The fast running pneumatic agitators are equipped with bearing and coupling housings. By means of the maintenance unit, pressurized air is enriched with oil for the vane drive. The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. Folding propellers that fit through the filling opening DN 150 mm are used for geared agitators. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. Explosion-proof mixers are also feasible.

The CRP-M tote tank mixers are featured with a pneumatic drive and were designed for the application in stainless steel tanks with filling openings of at least 400 mm and mixing volumes of 400 l to 1,500 l. The fast running pneumatic agitators are equipped with bearing and coupling housings. By means of the maintenance unit, pressurized air is enriched with oil for the vane drive. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening of at least 400 mm when being inserted. All CRP-M series can be supplied as follows: Lid Muffler Explosion-protection design

The GLP is a pneumatic top-entry series agitator that is used for homogenizing, dispersing, emulsifying and suspending in vessels and for viscosities up to 500 mPas for instance in wastewater treatment, chemical and cosmetics as well as in food industries. The agitator speed adapts to the viscosity of the media being mixed. Compact and easy-to-maintain construction as well as low weight. Power transmission via elastic coupling in the bearing housing. The agitator shaft has a double bearing in an aluminum housing separated from the drive. Speed is sensitively and continuously adjustable, smooth start, insensitive to vapor, dust and smoke. Compressed air keeps all moving parts clean. Insensitive to heat, suitable for high ambient temperatures. Compressed air, expanding in the air engine cools the agitator drive. Includes filters, pressure reducers with pressure gauge that indicates the secondary pressure. Available with a vessel clamp to fix the GLP on a drum.

The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M series mixers can be supplied as follows:

Le processor grand volume consiste en des réacteurs chauffés disposés horizontalement avec un arbre double (co- ou contrarotatif) qui permettent un mélange et un malaxage intensifs. Les processeurs grand volume Reasil et Reacom sont caractérisés par les avantages suivants: Très grands volumes Les viscosités les plus élevées (jusqu'à 15 000 Pas) et les solides peuvent être traités efficacement Traitement à faible cisaillement Des temps de séjour longs obtenus de manière économique Mélange, dévolatilisation, réaction et changement de phase (de thermofusible à solide) peuvent avoir lieu dans le même. Un système de dévolatilisation ou de réaction réussi est composé d’un processeur bien conçu intégré dans un système correctement étudié et réalisé. Buss-SMS-Canzler peut fournir le système complet, comprenant des services d'installation et de démarrage.

Filmtruder and Viscon processors are specialized in the concentration, purification and devolatilization of products with viscosities up to 10,000 Pa (s) and are characterized by the following properties: Agitated thin film processing Unequaled surface renewal, resulting in the lowest residual volatile content Typically no stripping agents required Large free vapour volume compared to product hold-up, allowing very high volatile removal in one stage A successful thin film processing system consists of the right processor design integrated with properly engineered subsystems. SMS can provide a complete system, including installation and start-up services, or full engineering and design documentation to allow you to add the necessary subsystems for our thin film processor. Heating temperature:20 - 400°C Pressure (process side):< 1 mbar - 30 bar Product viscosity:20-10.000 Pa·s Operation mode:Continuous

The direct driven agitator SPR is Geppert Ruhrtechnik’s solution for all industrial mixing tasks that demand a turbulent mixing with high peripheral speeds. It is driven by a three-phase-motor with poles between 2 and 8 as well as drive ratings between 0.25 kW and 75.0 kW. The SPR could also be equipped with a frequency inverter upon request (up to 7.5 kW). The agitator shaft is directly connected at the shaft journal of the drive via sleeve or flange coupling. Solutions with quick-change or precisions-change coupling are also feasible for lower drive ratings of up to 3.0 kW. The standard agitator element is a propeller. Other mixing elements according to the mixing task upon request. The SPR can be mounted as a stationary unit or – at a weight of up to 25 kg – it can also be mounted directly onto the open tank via a vessel clamp Up to motor size 112, all SPR series agitators can also be provided with reinforced shaft. Type test certificate numbers for zone 0 (category 1).

Rigid stand for wall-mounting for tank volumes from 100 l. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg can be realized. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching agitator elements. The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The electric or pneumatic supply is guided through a laterally mounted energy chain. The stand WRW is available in two standard sizes, thus enabling the processing of various tank sizes. The standard sizes are particularly designed for the processing of exchangeable vessels such as drums and IBCs.

Pneumatic drum mixer for highly viscous media. The FRP-HX is Geppert Ruhrtechnik’s drum mixer for highly viscous media of up to 5,000 mPas. The foldable mixing elements with a diameter of 200 mm demand a non-vertical installation in the drums. This installation is realized due to a traverse with a welded 2”-socket. Additionally the traverse allows the use of the agitator when the drum is open. The mobile mixer FRP-HX is by default equipped with a maintenance unit for the oiling of the pressurized air and mufflers. Special solution for highly viscous liquids of up to 5,000 mPas. Explosion-proof design after ATEX (2014/34/EU) for operation in ex-zones 0-2 for gases and zones 20-22 for dusts (device group II, category 1-3).

Electric drum mixer for highly viscous media. The FR-HX is Geppert Ruhrtechnik’s drum mixer for highly viscous media of up to 5,000 mPas. The foldable mixing elements with a diameter of 200 mm demand a non-vertical installation in the tank. This installation is realized due to a traverse with a welded 2”-socket. Additionally the traverse allows the use of the agitator when the drum is open. The mobile mixer FR-HX is by default equipped with an on-/off-switch with low voltage breaker and – upon request – with a connection cable. . The FR-HX could also be equipped with a frequency inverter upon request. Explosion-proof design after ATEX (2014/34/EU) for operation in ex-zones 0-2 for gases and zones 20-22 for dusts (Device group II, category 1-3).

KRK coaxial agitator features two different impeller systems for parallel mixing. The KRK has two interdependent agitator shafts with a different number of revolutions that move in opposite directions. The faster agitator shaft is supported in the slower hallow shaft of the geared mixing unit. The KRK series is primary suitable for the dispersing of highly viscous media. The heat transfer is promoted. Explosion-proof series certified to ATEX Directive 2014/34/EU zone 0 and zone 1.

The FR series is a fast running electric drum mixer that can directly be mounted on 200 l steel drums with a 2“ bung hole. The mounting on the drum is done with a 2” threaded adapter with which the agitator is screwed into the bung hole. The agitator shaft is connected to the drive shaft by means of a sleeve coupling. Folding propellers are used as mixing elements, which can be inserted into the drum through the 2” bung hole when being folded. The FR series mobile mixer is delivered as a turn-key solution with an on-/off-switch with low voltage breaker and connection cable. Upon request, the FR series mixer can also be supplied with an integrated frequency inverter. Additionally we can provide you with a vessel clamp applicable for open lid drums.

Star Burst 10 ist eine Nasspulverisierungsanlage zum Pulverisieren, Emulgieren, Dispergieren und Spalten von Medien durch Schrägstrahlkollision bei bis zu 2450 bar. Mittels zweier Druckverstärker wird ein kontinuierliches Druckniveau und ein stabiler Betrieb gewährleistet. Throughput:Max. 52 L/hour

Mehr Beratung. Mehr Kompetenz. Mehr als Vakuum. Stellen Sie sich vor, Sie müssen ein Volumen von 630 Kubikmetern evakuieren. Dies entspricht dem umbauten Raum eines Einfamilienhauses. Mit dieser Kammergröße werden heute Anlagen gebaut, in denen Teile mit einem Gewicht bis zu 50 Tonnen und Abmessungen bis zu 12 · 6 · 5 Metern im Elektronenstrahl-Schweißverfahren bearbeitet werden.

"Star Burst" ist eine Hochdruck-Dispergiervorrichtung vom Homogenisatortyp, die einen großen Vorteil darin hat, eine Feinpartikeldispersion mit minimaler Verunreinigung zu erzeugen. „Star Burst“ ist der ideale Partner bei der Entwicklung von Nanomaterialien und Advanced Materials durch Nassmahlen, Dispergieren, Emulgieren, Peelen und Delaminieren von Materialien mit Hochgeschwindigkeitsstrahlströmung. Throughput:max. 6 L/hour

Mit der neuen Duo 3 DC präsentiert Pfeiffer Vacuum eine zweistufige Drehschieberpumpe, die speziell für Anwendungen mit 24 Volt Gleichstrom konzipiert ist. Sie kann als einzige Drehschieberpumpe auf dem Markt im Temperaturbereich zwischen -20⁰C und +60⁰C eingesetzt werden. Mit einem Verbrauch von weniger als 100 Watt im Dauerbetrieb arbeitet sie enorm energieeffizient und ist dank des bürstenlosen Motors und der optionalen Magnetkupplung sehr wartungsarm.

Die Wälzkolbenpumpen der innovativen HiLobe® Baureihe bieten durch die individuelle Drehzahlregelung einen nominellen Saugvermögensbereich von 520 – 2.100 m3/h und sind somit perfekt auf kundenspezifische Anforderungen abstimmbar. Saugvermögen:520 – 2.100 m3/h Integrale Leckrate:1 · 10-6 Pa m3/s. Nennleistung bei maximaler Drehzahl:2 – 3,5 kW

Die neuen ATH M-Pumpen erreichen einen Gasdurchsatz von über 5.000 sccm für Stickstoff bei unbeheizten Anwendungen. Darüber hinaus bieten sie mit 1.500 sccm den höchsten am Markt verfügbaren Durchsatz für Argon sowie eine Pumpenbetriebstemperatur von 65 °C bei korrosiven Anwendungen.